Page 1 of 2

Unicorn pistol

Posted: Fri Nov 16, 2018 2:18 pm
by LDB415
I'd like to have a pistol about the size of a Glock 19 in profile but no more than 1 inch thick at it's widest point. Prefer 9mm but open to others. Anyone know of anything remotely approaching that size?

Re: Unicorn pistol

Posted: Fri Nov 16, 2018 3:01 pm
by mot7981
The Ruger Security 9 is listed at 1.02". Very similar to a G19 in size but much lower in cost. I picked one up a little while back and while I'm not crazy about it's curb appeal I've been pleased with it's reliability and accuracy.

Re: Unicorn pistol

Posted: Fri Nov 16, 2018 4:00 pm
by LDB415
Thanks. I'll do some research on that one. Anyone else with suggestions? The more the better.

Re: Unicorn pistol

Posted: Fri Nov 16, 2018 4:23 pm
by MaduroBU
Some of the kimber 1911 9mm guns might fit. The P365 might come close, but the barrel isn't 4".

Re: Unicorn pistol

Posted: Fri Nov 16, 2018 4:33 pm
by LDB415
I may go check out the P365. I don't have to have a 4" barrel. I want very thin but don't want to go down to a Kel-Tec size or similar.

Re: Unicorn pistol

Posted: Fri Nov 16, 2018 4:34 pm
by Flightmare
P365 is decent. I had fun shooting my new one on wednesday. If you haven't tried a M&P Shield 2.0, I would definitely recommend that as well.

Re: Unicorn pistol

Posted: Fri Nov 16, 2018 5:29 pm
by mot7981
The Kahr CT9 may also be worth a look if you're ok with a single stack (8+1). I would consider it sized between a 365 and the G19 and it's only .9" wide.

Re: Unicorn pistol

Posted: Fri Nov 16, 2018 5:36 pm
by oljames3
+1 for M&P Shield M2.0.

Re: Unicorn pistol

Posted: Fri Nov 16, 2018 6:00 pm
by LDB415
I think 7+1 capacity is my minimum. Other than that I don't have any deal breakers I can think of. I appreciate the suggestions for what to research.

Re: Unicorn pistol

Posted: Fri Nov 16, 2018 6:15 pm
by Jago668
The Sig P365 is going to be a decent bit smaller than a G19. Little small for my hands. If that doesn't bother you, it meets everything else with being exactly 1" wide/thick, and carries 10 rounds of 9mm. Shoots well, I could put all 10 rounds through a space between a quarter and a half-dollar even with it being small (and a rental shooting reloaded range ammo). A good many of your other G19 sized options are all going to be roughly the same width, around 1.3" wide/thick.

Re: Unicorn pistol

Posted: Fri Nov 16, 2018 8:23 pm
by uthornsfan
Para carry 9

Re: Unicorn pistol

Posted: Sat Nov 17, 2018 12:33 am
by The Annoyed Man
Most of the reputable manufacturers’ single-stack 9mms would fit your requirements. They each measure their guns’ widths a little differently from the others, but this should give you an idea.

Glock 43 - .87” wide at the slide.
Springfield XDS 9 - .9” wide at the grips.
S&W Shield 9mm - .95” wide at the frame.
Sig 938 - 1.1” overall width
Sig P365 - 1.0” overall width.

Re: Unicorn pistol

Posted: Sat Nov 17, 2018 9:08 am
by mrvmax
I carry the G43 with Taran Tactical +3 mag bases. In my younger years I’ve carried large pistols concealed (with a Para 14-45 being the largest I’ve used for EDC. That double stack 45 was heavy and big) but even my G29 feels large for EDC now. I’ve settled into carrying smaller 9’s for EDC.

Re: Unicorn pistol

Posted: Sat Nov 17, 2018 10:12 am
by Setxjeff
SCCY light weight dbl stack 9 mm 10+1. I have 2 and both have fired everything I have put in them. The mags use the same diameter and feed lip arrangement as my ruger P85 ,so with 1 extra notch mags are interchangeable