Had a fun afternoon with my new 1911....

Gun, shooting and equipment discussions unrelated to CHL issues

Moderator: carlson1


Topic author
cyphur
Senior Member
Posts in topic: 5
Posts: 1334
Joined: Fri Jun 23, 2006 10:02 am
Location: DFW, Tx

Had a fun afternoon with my new 1911....

#1

Post by cyphur »

...breaking it in. Put 300 rounds of WWB 230gr FMJ through some paper this afternoon through my "new" Kimber Tactical Ultra II. It functioned flawlessly except for a few FTFs(NO FTEs thankfully). I think its mostly the Kimber mag producing those errors, as its usually the last round on the Kimber mag. Going to order the Wilson conversion kit tomorrow as well as another magazine tomorrow, who has the best prices?


I had been told some horror stories about the External Extractor(which is what mine is) but I am thankful to announce it does not seem I will need to get in touch with Kimber just yet, as mine functions well. It will need 500 or so rounds more before I can declare it "carry ready" - the break-in plus 250 trouble-free rounds.

Also learned how to field strip a 1911 without a disassembly tool tonite! LOL. I had taken it apart before taking it to the range, to clean and lube it. However I had the darndest time getting the spring and GR assembly out - didn't in fact. After today at the range, and the oil getting cycled through it, it came out like a charm.



Question - what do you all use to lube your handguns? I currently am using RemOil as I have it for my Rem700. I figure you all have your preferences, care to share? Thanks!

MrDrummy
Senior Member
Posts in topic: 1
Posts: 271
Joined: Thu Jul 06, 2006 1:33 am
Location: Lubbock, TX
Contact:

#2

Post by MrDrummy »

That's a nice little gun, Cyphur.

I've got a Stainless Ultra Carry that goes everywhere with me. I never ran into any FTF's, but I was using the Wilson 47OX from the start. I didn't WANT to run into any problems after spending as much as I did!

I still can't get my recoil spring assembly out without that little tool. I can't get it over the barrell link. How'd you do it?

I was using plain ol' Hoppes for mine until I ran across a guy using the Hoppes Elite oil. I love it. I figure that the stuff has been working for years, and an improvement on something that has been working has got to be good. I've had no problems yet! Well, my only problem is that oil is so slippery that I can't keep it in the bottle. It leaks all over the place.

Keep shootin' that thing, and let me know how it goes!

txinvestigator
Senior Member
Posts in topic: 2
Posts: 4331
Joined: Wed May 04, 2005 6:40 pm
Location: DFW area
Contact:

Re: Had a fun afternoon with my new 1911....

#3

Post by txinvestigator »

cyphur wrote:.... Going to order the Wilson conversion kit tomorrow as well as another magazine tomorrow, who has the best prices?

WHat is that?
*CHL Instructor*


"Speed is Fine, but accuracy is final"- Bill Jordan

Remember those who died, remember those who killed them.

Johnny
Junior Member
Posts in topic: 2
Posts: 41
Joined: Mon Jun 12, 2006 6:19 pm

#4

Post by Johnny »

I prefer CLP for the internal works and a slight dab of Petrol-Gel aluminum grease on the slide rails and hammer/bottom rail. An NLGI#0 aluminum grease would be just perfect, but it's dang hard to find.

A FTF on the last round does beg a certain question. What kind of mag follower are you using? I don't know too much about Kimber mags, but I'll wager that the one you're having trouble with is a round-top with no dimple. Can't stand those, myself. I guess you've deduced that your last round is "jumping the gun" and getting ahead of the slide. I'm not privvy to any secret information from Kimber, so this is a guess, but I'm thinking that most of the horrors stemming from the external extractor come from it being less tolerant of bad followers and springs.

Do be sure to stay away from Devel followers (or anything else with poor support on the rear end) and never shoot aggressive hollowpoints like Golden Sabers. Otherwise, you'll be calling the guys at Rogers Precision about feedramp inserts. If the Wilson kits are still using those clunky plastic followers, you should be just fine. SXTs are probably your best bet for hollowpoints as they have a nice gentle shape that won't strip the anodizing right off. Alloy guns require you to be very gentle with your feedramp.

Oh, and where are the pictures? :grin:

Topic author
cyphur
Senior Member
Posts in topic: 5
Posts: 1334
Joined: Fri Jun 23, 2006 10:02 am
Location: DFW, Tx

#5

Post by cyphur »

MrDrummy, it was just a matter of angle and a little twist. Putting it back in was much more troublesome than getting it out.


TXI - its a little kit you buy from Wilson that converts the internals of a magazine to their style. It helps in a couple ways, especially with an aluminum framed weapon.


I'll try to get pics tonite. :grin:

Edited for spelling.
Last edited by cyphur on Fri Aug 25, 2006 8:30 am, edited 2 times in total.

Cosmo 9
Senior Member
Posts in topic: 1
Posts: 549
Joined: Tue Dec 13, 2005 2:43 pm
Location: Lewisville, TX

#6

Post by Cosmo 9 »

Glad to see that you are no longer handgun challenged :woohoo
These Pretzels are making me thirsty!

barnett
Junior Member
Posts in topic: 1
Posts: 31
Joined: Mon Aug 07, 2006 6:51 am
Location: plano

#7

Post by barnett »

i have a Kimber Custom Eclipse II that had a couple of FTFs with the Kimber mags. switched to Wilson mags and not a problem since!

txinvestigator
Senior Member
Posts in topic: 2
Posts: 4331
Joined: Wed May 04, 2005 6:40 pm
Location: DFW area
Contact:

#8

Post by txinvestigator »

cyphur wrote:

TXI - its a little kit you buy from Wilson that converts the internals of a magazine to their style. It helps in a couple ways, especially with an aluminum framed weapon.

Edited for spelling.
I see. Is that less expensive than new Wislons?
*CHL Instructor*


"Speed is Fine, but accuracy is final"- Bill Jordan

Remember those who died, remember those who killed them.

Topic author
cyphur
Senior Member
Posts in topic: 5
Posts: 1334
Joined: Fri Jun 23, 2006 10:02 am
Location: DFW, Tx

#9

Post by cyphur »

Well, the reason you change out the follower is because it could damage the frame. No reason to stop using a mag you can convert.

But yes - its markedly cheaper. The spring/follower kit is ~$8, compared to the $20+ I'll pay for a new mag.

I'm going to purchase a few new magazines anyhow.

WNallG30
Member
Posts in topic: 1
Posts: 107
Joined: Wed Mar 22, 2006 8:59 am
Location: Odessa, TX

#10

Post by WNallG30 »

I didn't know Wilson had conversion kits. I'll have to get a few of those. I've tried several mag with my Raptor II and I like the Wilson's best. I've got 3 now, 1 in the weapon for carry and 2 spares on my belt. The Chip McCormick's are good too. I was kinda scared to post here, I still haven't posted pics of my Raptor, I'm sure I'll hear about it again too! ;-) Congrats on the new pistola Cyphur! Did you go with that instead of the Sigs you were considering or still looking at the Sig? I'd like a Sig myself one of these days. I really like the SAS models.

Topic author
cyphur
Senior Member
Posts in topic: 5
Posts: 1334
Joined: Fri Jun 23, 2006 10:02 am
Location: DFW, Tx

#11

Post by cyphur »

http://www.wilsoncombat.com/a_springs_followers.asp

Thats the link.


I'm still looking at Sigs, but thats a little down the road.

Madsmiley
Member
Posts in topic: 1
Posts: 50
Joined: Thu Aug 10, 2006 4:06 pm
Location: League City

#12

Post by Madsmiley »

That what I use for a carry piece never had any issue with it...One thing I do highly recommend it to change out the springs somewhere around 1000-1200 rounds.. ;-) A little trick to taking these things down...Eventually you will probably lose the take down tool that came with it..I think mine lasted all of about 47 seconds after I got it home before it decided to disappear..Anyway, a common staple or paperclip can be bent and used for this just as good..

Topic author
cyphur
Senior Member
Posts in topic: 5
Posts: 1334
Joined: Fri Jun 23, 2006 10:02 am
Location: DFW, Tx

#13

Post by cyphur »

Yea, my tool disappeared sometime between wednesday nite and thursday nite. I don't think I'll ever find that little bugger.


It comes apart fine w/o the tool, until you try to take the spring assembly apart. No bueno.....

Reysc
Senior Member
Posts in topic: 1
Posts: 733
Joined: Tue Mar 07, 2006 12:07 pm
Location: Dallas

#14

Post by Reysc »

cyphur wrote:http://www.wilsoncombat.com/a_springs_followers.asp

Thats the link.


I'm still looking at Sigs, but thats a little down the road.
Cyphur, there are the mags ans spring upgrades I've been using and so far it great.. Even my original colt combat 6*1 mag was trouble free after I've upgraded the spring/follower..

http://www.trippresearch.com/products/u ... pgrade.htm

Rey

KBCraig
Banned
Posts in topic: 1
Posts: 5251
Joined: Fri May 06, 2005 3:32 am
Location: Texarkana

#15

Post by KBCraig »

cyphur wrote:Well, the reason you change out the follower is because it could damage the frame.
Okay, I'm dense, and don't have a 1911 to look at. :cry:

But how does a magazine follower damage the frame?
Post Reply

Return to “General Gun, Shooting & Equipment Discussion”