Unicorn pistol

Gun, shooting and equipment discussions unrelated to CHL issues

Moderator: carlson1

User avatar

Topic author
LDB415
Senior Member
Posts in topic: 4
Posts: 1662
Joined: Sat Jun 21, 2014 12:01 am
Location: Houston south suburb

Unicorn pistol

#1

Post by LDB415 »

I'd like to have a pistol about the size of a Glock 19 in profile but no more than 1 inch thick at it's widest point. Prefer 9mm but open to others. Anyone know of anything remotely approaching that size?
It's fine if you disagree. I can't force you to be correct.
NRA Life Member, TSRA Life Member, GSSF Member
A pistol without a round chambered is an expensive paper weight.

mot7981
Senior Member
Posts in topic: 2
Posts: 224
Joined: Thu Jan 19, 2012 5:17 pm
Location: West Houston

Re: Unicorn pistol

#2

Post by mot7981 »

The Ruger Security 9 is listed at 1.02". Very similar to a G19 in size but much lower in cost. I picked one up a little while back and while I'm not crazy about it's curb appeal I've been pleased with it's reliability and accuracy.
User avatar

Topic author
LDB415
Senior Member
Posts in topic: 4
Posts: 1662
Joined: Sat Jun 21, 2014 12:01 am
Location: Houston south suburb

Re: Unicorn pistol

#3

Post by LDB415 »

Thanks. I'll do some research on that one. Anyone else with suggestions? The more the better.
It's fine if you disagree. I can't force you to be correct.
NRA Life Member, TSRA Life Member, GSSF Member
A pistol without a round chambered is an expensive paper weight.

MaduroBU
Senior Member
Posts in topic: 1
Posts: 702
Joined: Sat Nov 12, 2016 9:11 am

Re: Unicorn pistol

#4

Post by MaduroBU »

Some of the kimber 1911 9mm guns might fit. The P365 might come close, but the barrel isn't 4".
User avatar

Topic author
LDB415
Senior Member
Posts in topic: 4
Posts: 1662
Joined: Sat Jun 21, 2014 12:01 am
Location: Houston south suburb

Re: Unicorn pistol

#5

Post by LDB415 »

I may go check out the P365. I don't have to have a 4" barrel. I want very thin but don't want to go down to a Kel-Tec size or similar.
It's fine if you disagree. I can't force you to be correct.
NRA Life Member, TSRA Life Member, GSSF Member
A pistol without a round chambered is an expensive paper weight.
User avatar

Flightmare
Senior Member
Posts in topic: 1
Posts: 3095
Joined: Wed Mar 09, 2016 7:00 pm
Location: Plano, TX

Re: Unicorn pistol

#6

Post by Flightmare »

P365 is decent. I had fun shooting my new one on wednesday. If you haven't tried a M&P Shield 2.0, I would definitely recommend that as well.
Deplorable lunatic since 2016

mot7981
Senior Member
Posts in topic: 2
Posts: 224
Joined: Thu Jan 19, 2012 5:17 pm
Location: West Houston

Re: Unicorn pistol

#7

Post by mot7981 »

The Kahr CT9 may also be worth a look if you're ok with a single stack (8+1). I would consider it sized between a 365 and the G19 and it's only .9" wide.
User avatar

oljames3
Senior Member
Posts in topic: 1
Posts: 5355
Joined: Sat Jun 14, 2014 1:21 pm
Location: Elgin, Texas
Contact:

Re: Unicorn pistol

#8

Post by oljames3 »

+1 for M&P Shield M2.0.
O. Lee James, III Captain, US Army (Retired 2012), Honorable Order of St. Barbara
2/19FA, 1st Cavalry Division 73-78; 56FA BDE (Pershing) 78-81
NRA, NRA Basic Pistol Shooting Instructor, Rangemaster Certified, GOA, TSRA, NAR L1
User avatar

Topic author
LDB415
Senior Member
Posts in topic: 4
Posts: 1662
Joined: Sat Jun 21, 2014 12:01 am
Location: Houston south suburb

Re: Unicorn pistol

#9

Post by LDB415 »

I think 7+1 capacity is my minimum. Other than that I don't have any deal breakers I can think of. I appreciate the suggestions for what to research.
It's fine if you disagree. I can't force you to be correct.
NRA Life Member, TSRA Life Member, GSSF Member
A pistol without a round chambered is an expensive paper weight.
User avatar

Jago668
Senior Member
Posts in topic: 1
Posts: 992
Joined: Sun May 03, 2015 12:31 am

Re: Unicorn pistol

#10

Post by Jago668 »

The Sig P365 is going to be a decent bit smaller than a G19. Little small for my hands. If that doesn't bother you, it meets everything else with being exactly 1" wide/thick, and carries 10 rounds of 9mm. Shoots well, I could put all 10 rounds through a space between a quarter and a half-dollar even with it being small (and a rental shooting reloaded range ammo). A good many of your other G19 sized options are all going to be roughly the same width, around 1.3" wide/thick.
NRA Benefactor Member

uthornsfan
Senior Member
Posts in topic: 1
Posts: 490
Joined: Sun Jan 30, 2011 11:13 pm
Location: Austin, TX

Re: Unicorn pistol

#11

Post by uthornsfan »

Para carry 9
User avatar

The Annoyed Man
Senior Member
Posts in topic: 1
Posts: 26852
Joined: Wed Jan 16, 2008 12:59 pm
Location: North Richland Hills, Texas
Contact:

Re: Unicorn pistol

#12

Post by The Annoyed Man »

Most of the reputable manufacturers’ single-stack 9mms would fit your requirements. They each measure their guns’ widths a little differently from the others, but this should give you an idea.

Glock 43 - .87” wide at the slide.
Springfield XDS 9 - .9” wide at the grips.
S&W Shield 9mm - .95” wide at the frame.
Sig 938 - 1.1” overall width
Sig P365 - 1.0” overall width.
“Hard times create strong men. Strong men create good times. Good times create weak men. And, weak men create hard times.”

― G. Michael Hopf, "Those Who Remain"

#TINVOWOOT

mrvmax
Senior Member
Posts in topic: 1
Posts: 2023
Joined: Tue Oct 25, 2005 7:16 pm
Location: Friendswood

Re: Unicorn pistol

#13

Post by mrvmax »

I carry the G43 with Taran Tactical +3 mag bases. In my younger years I’ve carried large pistols concealed (with a Para 14-45 being the largest I’ve used for EDC. That double stack 45 was heavy and big) but even my G29 feels large for EDC now. I’ve settled into carrying smaller 9’s for EDC.

Setxjeff
Member
Posts in topic: 1
Posts: 148
Joined: Fri May 30, 2014 4:24 pm
Location: South Newton County

Re: Unicorn pistol

#14

Post by Setxjeff »

SCCY light weight dbl stack 9 mm 10+1. I have 2 and both have fired everything I have put in them. The mags use the same diameter and feed lip arrangement as my ruger P85 ,so with 1 extra notch mags are interchangeable
TSRA Member
M1 Garand Collectors Association
Post Reply

Return to “General Gun, Shooting & Equipment Discussion”